Rapid Pump & Meter Service Co., Inc.
285 Straight Street
P.O. Box AY
Paterson, NJ, 07509 USA
Phone:973.345.5600 • Fax: 973.345.0301
Email: info@servicer.com
• Website:
www.rapidservice.com
|
|
|
Item # 8VL600M6-43, Standard 8" Submersible Non-Clog Wastewater Pumps
|
|
|
|
|
|
Capacity : 3,875 gpm (14,667 lpm)
Head : 170 ft (50.8 m)
Standard (8VL) and Explosion-Proof (8VLX)
The Myers 8VL submersible non-clog Sewage Pumps are designed especially for high flow applications such as: Large Municipal lift stations, treatment plants, transfer stations and dewatering. A quick removal type rail system is available to simplify installation and maintenance. The 8VL's ability to handle solids up to 4 inches in diameter and 3 available motor speeds make it ideal for most high flow wastewater applications.
Advantages By Design
High efficiency hydraulic design cuts pumping costs and extends life of fluid end components.
- Two-vane, rounded port impellers handle solids with ease at high operating efficiencies.
- Modified, constant velocity volute offers quiet operation, low radial loads over extended portion of performance curve.
Durable motor will deliver many years of reliable service
- Oil-filled motor and seal cavity for maximum heat dissipation and continuous bearing lubrication.
- Heat sensor thermostats imbedded in windings protect motor from overheat conditions.
- Seal leak probes warn of moisture entry: helps prevent costly motor burn-out.
|
|
|
|
|
|
Head
|
|
170 ft
51.8 m
|
|
|
|
Solids Handling (Diameter)
|
|
4 in
101.6 mm
|
|
|
|
Liquids Handling
|
|
Drain Water
Effluent
Raw Unscreened Sewage
|
|
|
|
Intermittent Liquid Temperature
|
|
up to 140 ºF
up to 60 ºC
|
|
|
|
Winding Insulation Temperature. (Class H)
|
|
356 ºF
180 ºC
|
|
|
|
Motor Electrical Data
|
|
1150 RPM: 30, 40, 50 hp, 3 ph
230, 460, 575 volts, 60 Hz
60 hp, 3 ph
460 & 575 volts, 60 Hz
1750 RPM: 75,100, 125 hp, 3 ph
460 & 575 volts, 60 Hz
870 RPM: 15, 20, 25 hp, 3 ph
208, 230, 460 & 575 volts, 60 Hz
|
|
|
|
Acceptable pH Range
|
|
6 to 9
|
|
|
|
Specific Gravity
|
|
0.9 to 1.1
|
|
|
|
Viscosity
|
|
28 to 35 SSU
|
|
|
|
Horizontal Discharge
|
|
8 in
203.2 mm
|
|
|
|
Speed
|
|
1150 rpm
|
|
|
|
Power
|
|
60 hp
|
|
|
|
Voltage
|
|
460 V
|
|
|
|
Phase
|
|
3
|
|
|
|
Frequency
|
|
60 Hz
|
|
|
|
Start
|
|
405 A
323 kV·A
|
|
|
|
Run
|
|
82.7 A
51.4 kW
65.9 kV·A
|
|
|
|
NEC Code Letter
|
|
F
|
|
|
|
Service Factor
|
|
101.0 A
62.7 kW
1.2
|
|
|
|
Capacity
|
|
3,875 gpm
14,667 lpm
|
|
|
|
Note
|
|
Consult factory for applications outside of these recommendations.
|
|
|
|
|
|
|
Motor Housing Material
|
|
Cast Iron, Class 30, ASTM A48
|
|
|
|
Seal Housing Material
|
|
Cast Iron, Class 30, ASTM A48
|
|
|
|
Volute Case Material
|
|
Cast Iron, Class 30, ASTM A48
|
|
|
|
Cord Cap Material
|
|
Cast Iron, Class 30, ASTM A48
|
|
|
|
Enclosed 2-Vane Impeller Material
|
|
Ductile Iron, Class 65, ASTM A536
|
|
|
|
Power Cord Material
|
|
25 ft. SOOW
|
|
|
|
Control Cord Material
|
|
25 ft. SOOW
|
|
|
|
Standard Double Tandem Mechanical Seal Material
|
|
Carbon & Ceramic
|
|
|
|
Optional Double Tandem Mechanical Seal Material
|
|
Lower Tungsten, Carbide
|
|
|
|
Pump Shaft Material
|
|
416 SST
|
|
|
|
Motor Shaft Material
|
|
416 SST
|
|
|
|
Fasteners Material
|
|
300 series SST
|
|
|
|
Case Wear Ring Materials
|
|
Bronze
|
|
|
|
|
|
|
Agency Approvals
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
